鋁合金卷簾門作為比較常見的產品，自然也會出現問題，比較常見的問題就是門體運轉速度下降或干脆不動了，而造成這些毛病的原因是有很多的。那么鋁合金卷簾門不能快速運行怎么辦?下面看看濟南卷簾門廠給大家介紹吧。

As a common product, aluminum alloy roller shutter doors naturally have problems. The common problem is that the door body slows down or simply stops moving. There are many reasons for these problems. What if the aluminum alloy roller shutter door can not run quickly? Now let's take a look at Jinan Rolling Door Factory and introduce it to you.

1.操控失效故障發生的部位及要素有繼電器(接觸器)觸點粘死、行程微動開關失效或觸片變形、滑塊緊定螺釘松、靠板螺絲松使靠板移位,使滑塊或螺母不能隨絲桿轉動而移動、限位器傳動齒輪破損、按鈕上、下鍵卡死。

1. The parts and elements of control failure failure include relay (contactor) contact sticking, stroke microswitch failure or contact deformation, loose slider set screws, and loose backup plate screws that cause the backup plate to move, so that the slider or nut cannot move with the screw rod rotation, the limiter transmission gear wheel is damaged, and the up and down buttons are stuck.

2.當鋁合金卷簾門無法發動或者是發動較慢的時候，先要查看電動機是否能夠正常運轉工作，若不能則更換電動機。然后查看機械部分有沒有卡住的當地，如有清除去即可。當出現控制器失效時,應先更換電源接觸器,然后更換傳動齒輪。

2. When the aluminum alloy roller shutter door cannot be started or starts slowly, check whether the motor can operate normally. If not, replace the motor. Then check if the mechanical part is stuck, and if so, remove it. In case of controller failure, replace the power contactor first, and then replace the transmission gear.

3.鋁合金卷簾門不能開關時，應先查看有無市電、保險管有無燒毀，如果保險絲溶斷了，就要做查看。在傳達室拔掉地下電纜插頭，用萬用表Rx1擋，丈量電機紅、白、黃三條引線是否相通，電阻應在15歐姆左右，與赤色應在30歐姆左右，再用R×10K檔丈量與其它的線是否有必定的電阻，主要是查看線與線之間是否會間接性短路。紅、白、黃三條電機線不通，再檢測機尾接線盒里的紅、白、黃線，若相通，闡明地下電纜中紅、白、黃斷路，不相通再拆開機罩，在門排與機頭銜接的插頭處再測這三條線，若相通，闡明從門排端起至傳達室的線斷，若仍是不通，直接丈量電機定子線圈是否斷路。

3. When the aluminum alloy roller shutter door cannot be opened and closed, check whether there is mains power and whether the fuse tube is burned. If the fuse is broken, check it. Unplug the underground cable plug in the reception room, block it with a multimeter Rx1, and measure whether the red, white and yellow leads of the motor are connected. The resistance should be about 15 ohms, and the red lead should be about 30 ohms. Then use R × The 10K gear is used to measure whether there is a certain resistance with other lines, mainly to check whether there is an indirect short circuit between lines. If the red, white and yellow motor wires are not connected, then check the red, white and yellow wires in the terminal box at the tail of the machine. If they are connected, explain that the red, white and yellow wires in the underground cable are open circuited. If they are not connected, remove the hood. Then measure the three wires at the plug connecting the door truss and the machine head. If they are connected, explain that the wire from the end of the door truss to the reception room is broken. If it is still not connected, directly measure whether the motor stator coil is open circuited.

4.當該門能關(開)不能開(關)，闡明電機中的白色公共線良好，能夠先測電機赤色與白色線是否相通，再丈量藍色與灰(綠)色信號線和K2傳感開關是否短路。

4. When the door can be closed (opened) but not opened (closed), it is clarified that the white common wire in the motor is in good condition. First, measure whether the red and white wires of the motor are connected, and then measure whether the blue and gray (green) signal wires and K2 sensor switch are short circuited.

以上是廠家給大家介紹的內容，關于鋁合金卷簾門、水晶卷簾門、車庫卷簾門、電動卷簾門等門類信息，關注我們廠家http://www.shaulmediation.com，我司專注從事卷簾門、車庫門安裝銷售，歡迎聯系我們!

The above is what the manufacturer has introduced to you. Pay attention to our manufacturers about aluminum alloy roller shutter doors, crystal roller shutter doors, garage roller shutter doors, electric roller shutter doors and other door categories http://www.shaulmediation.com Our company focuses on the installation and sales of rolling shutter doors and garage doors. Welcome to contact us!