卷簾門的負荷試門及調試這一步驟非常的關鍵，如果檢測沒有任何問題存在，那么以上就可以真的運行起來了；反之就要及時進行處理，下面濟南卷簾門廠來講講卷簾門的負荷試門及調試注意事項。

The load test and commissioning of the roller shutter door is very critical. If there is no problem in the detection, the above can really be run; On the contrary, it should be handled in time. Next, Jinan Rolling Door Factory will talk about the load test and commissioning precautions of rolling doors.

用手動運行，再電動運行數次。觀察判斷運行狀態，并作相應的調整，直至運行無卡死、阻滯、限位不準及異常噪聲，卷簾運行順暢為止。無誤后，拉動開閉機手動速放功能的可靠性。工程要求時，應安裝溫控自動釋放裝置，且易熔片應固定在外表面易受火的位置。

Operate manually and then electrically for several times. Observe and judge the operation state, and make corresponding adjustment until the operation is free of jamming, blocking, inaccurate limit and abnormal noise, and the roller shutter operates smoothly. After no error, pull the reliability of the manual quick release function of the switch. If required by the project, automatic temperature control release device shall be installed, and the fusible plate shall be fixed at the position where the external surface is vulnerable to fire.

注意事項：

matters needing attention:

1、產品在運輸過程中要平穩、牢固，避免碰撞損壞;輕抬輕放，嚴禁磕、摔、撬等行為，防止機械變形損壞產品，影響安裝使用。

1. The product shall be stable and firm during transportation to avoid collision damage; Lift and place with care. Knock, fall, pry and other behaviors are strictly prohibited to prevent mechanical deformation from damaging products and affecting installation and use.

2、安裝人員須注意施工安全，帶好安全帽，系好安全帶。

2. The installation personnel must pay attention to construction safety, wear safety helmets and fasten safety belts.

3、施工及調試期間，嚴禁卷簾下面站人和有行人通過，以防意外發生;在卷簾安裝部位應有醒目的“禁止通行”標志。

3. During construction and commissioning, it is strictly forbidden to stand under the roller shutter and pedestrians to pass through to prevent accidents; There shall be a striking "No Passage" sign at the installation position of the roller shutter.

4、安裝過程中要與水暖電安裝、吊頂安裝、石材施工、鋁板施工以及玻璃幕墻施工隊伍相互配合作業。

4. During the installation process, it shall cooperate with the construction teams of plumbing, ceiling, stone construction, aluminum plate construction and glass curtain wall.

5、安裝大小端板時，用水平管測量兩端板的一致。

5. When installing large and small end plates, use a horizontal tube to measure the consistency of the center of the two end plates.

卷簾門的負荷試門及調試注意事項相關信息就為您講解到這里了，您作為參考時要注意名字什么的，防止下順利使用。更多相關內容就來聯系我們http://www.shaulmediation.com咨詢吧！

This is the end of the information about the load test and commissioning precautions of the roller shutter door. You should pay attention to the name when you use it as a reference to prevent it from being used smoothly. Contact us for more information http://www.shaulmediation.com Consult!