卷簾門已經在市場中普及很多年了，我們的車庫、和工廠、商店的門大多都是使用的卷簾門。下面濟南卷簾門廠來給大家講解下卷簾門使用時部件系統出現問題的原因以及處理。

Curtain doors have been popular in the market for many years. Most of the doors of our garages, factories and stores are rolling doors. Next, Jinan Rolling Door Factory will explain the causes and solutions of the problems of the component system when rolling doors are used.

1、電動機不動或轉速慢

1. The motor does not move or the speed is slow

故障原因：一般是線路斷路、電機燒損、停止按鈕沒復位、限位開關動作、負載較大等引起。

Fault cause: generally, it is caused by circuit break, motor burning, stop button not reset, limit switch action, heavy load, etc.

處理方法：檢查線路、并接通；更換燒損電機；更換按鈕或重復按動幾次；撥動限位開關滑塊使它脫離微動開關觸點，并調整微動開關位置；檢查機械部分有無卡阻，若有則消除卡阻清理障礙物。

Treatment method: check the line and connect it; Replace the burning motor; Replace the button or press it repeatedly several times; Toggle the limit switch slider to separate it from the microswitch contact, and adjust the microswitch position; Check whether the mechanical part is jammed. If so, remove the jamming and clear the obstacles.

2、控制失效

2. Control failure

故障發生的部位及原因：繼電器(接觸器)觸點粘死、行程微動開關失效或觸片變形、滑塊緊定螺釘松、靠板螺絲松使靠板移位，使滑塊或螺母不能隨絲桿轉動而移動、限位器傳動齒輪破損、按鈕上、下鍵卡死。

Parts and causes of failure: relay (contactor) contact is stuck, stroke microswitch is invalid or contact piece is deformed, slider set screw is loose, and backup plate screw is loose, which makes backup plate move, so that slider or nut cannot move with screw rod rotation, limiter transmission gear is damaged, and up and down buttons are stuck.

處理方法：更換繼電器(接觸器)；更換微動開關或觸片；緊定滑塊螺釘并使靠板復位；更換限位器傳動齒輪；更換按鈕。

Handling method: replace the relay (contactor); Replace the microswitch or contact; Tighten the slider screws and reset the backup plate; Replace the limiter transmission gear; Replace the button.

3、手拉鏈不動

3. The hand zipper does not move

故障原因：環形鏈條堵住十字槽；棘爪無脫離棘輪；壓鏈架卡死。

Fault cause: the cross groove is blocked by the ring chain; The pawl does not disengage from the ratchet wheel; The chain pressing frame is stuck.

處理方法：理順環形鏈條；調整棘爪與壓鏈架相對位置；更換或潤滑銷軸。

Treatment method: straighten out the ring chain; Adjust the relative position of the pawl and the chain pressing frame; Replace or lubricate the pin shaft.

4、電機振動或噪聲較大

4. The motor has large vibration or noise

故障原因：剎車盤不平衡或斷裂；剎車盤無緊固；軸承失油或失效；齒輪嚙合不順、失油或磨損嚴重；電機電流聲或振動。

Fault cause: the brake disc is unbalanced or broken; The brake disc is not fastened; Bearing oil loss or failure; Gear engagement is not smooth, oil loss or serious wear; Motor current sound or vibration.

處理方法：更換剎車盤或重新調整平衡；緊固剎車盤螺母；更換軸承；修配電機軸輸出端齒輪、潤滑或更換；檢查電機，如電機壞損則更換。

Treatment method: replace the brake disc or readjust the balance; Tighten the brake disc nut; Replace the bearing; Repair, lubricate or replace the motor shaft output end gear; Check the motor and replace it if it is damaged.

卷簾門使用時部件系統出現問題的分析就從四個方面來講解完畢了。您對此有什么問題或者疑惑或者需求都可以隨時來我們網站http://www.shaulmediation.com進行咨詢！

The analysis of the problems of the component system when the roller shutter door is used is completed from four aspects. You can come to our website at any time if you have any questions or doubts or needs http://www.shaulmediation.com Consult!