在快速門系列產品中，快速卷簾門對安裝要求是非常高的，需要結合實際門洞情況來定安裝方案，結合快速卷簾門的安裝示意圖，濟南卷簾門廠來講解一下快速門在安裝中需要注意的各個要點。

Among the fast shutter series products, the fast shutter door has very high installation requirements, so the installation scheme needs to be determined according to the actual door opening situation. In combination with the installation diagram of the fast shutter door, Jinan Rolling Door Factory will explain the key points that need to be paid attention to in the installation of the fast shutter door.

1、安裝快速門的門洞上方需要一定的空間來安裝快速卷簾門機頭，快速卷簾門的機頭是一個比較規則的長方體，通常情況下機頭下方會預留200mm高度的預留空間，所以機頭的上方空間為A+200mm，機頭的高度A的大小會受到門洞高度的影響，門洞高度越大機頭的高度A也會越大，如果門洞上方空間較小，可以通過加裝一塊門板，將預留的200mm空間省略掉。

1. A certain space is required above the door opening where the fast shutter door is installed to install the head of the fast shutter door. The head of the fast shutter door is a regular cuboid. Normally, a space of 200mm is reserved below the head, so the space above the head is A+200mm. The height A of the head will be affected by the height of the door opening. The higher the door opening is, the higher the head height A will be. If the space above the door opening is small, The reserved 200mm space can be omitted by adding a door panel.

也可以讓機頭吃一部分洞口高度，當然須加裝一塊門板，這樣在不至于門洞會留有縫隙;機頭的厚度，圖中所示的B的數值，B的大小也會根據門洞大小有相應的尺寸大小，通常情況下機頭厚度不會對安裝造成影響，特別的情況下需要具體注意測量;機頭的寬度，機頭的寬度是大于門洞的寬度的，如果門洞的墻面不平整，要注意機頭寬的安裝要求為：門洞寬度+立柱跨度*2+100mm。

You can also let the handpiece eat part of the hole height. Of course, a door panel must be installed to avoid gaps in the door opening; The thickness of the machine head, the value of B shown in the figure, and the size of B will also have a corresponding size according to the size of the door opening. Generally, the thickness of the machine head will not affect the installation, and special attention should be paid to the measurement under special circumstances; The width of the handpiece, the width of the handpiece is greater than the width of the door opening. If the wall of the door opening is uneven, pay attention to the installation requirements of the handpiece width: door opening width+column span * 2+100mm.

2、門洞寬度方面需要注意的是，門洞寬度并不是快速卷簾門的安裝寬度，門洞寬度通常是開啟寬度，而安裝寬度為：開啟寬度+立柱寬度*2，立柱寬度為圖中所示C的數值，立柱寬度的大小也受到門洞寬度的影響。如果門洞是在一個平整的墻面上，只需考慮墻體的堅固性即可，通常都能滿足快速卷簾門安裝寬度要求。

2. In terms of the door opening width, it should be noted that the door opening width is not the installation width of the quick roll up door. The door opening width is usually the opening width, while the installation width is: opening width+column width * 2. The column width is the value of C shown in the figure. The column width is also affected by the door opening width. If the door opening is on a flat wall, just consider the firmness of the wall, which can generally meet the requirements for the installation width of the fast rolling shutter door.

在快速卷簾門安裝的時候，除了需要著重注意以上兩點外，還需要注意地面的水平性、門洞上下寬度是否一致、門洞兩次墻面是否在一個水平面上等問題。

In addition to the above two points, attention should be paid to the levelness of the ground, whether the upper and lower widths of the door openings are consistent, and whether the two walls of the door openings are on the same horizontal plane.

快速卷簾門不同于普通卷簾門，由于智能化成都較高，好能有正規的專門的快速卷簾門廠家的技術人員現場指揮安裝。您可以來我們網站http://www.shaulmediation.com咨詢看看！

The quick rolling shutter door is different from the ordinary rolling shutter door. Due to the high intelligence of Chengdu, it is good to have the technicians of the formal and specialized fast rolling shutter door manufacturer to direct the installation on site. You can come to our website http://www.shaulmediation.com Consult!