<p id="ttrrv"><cite id="ttrrv"></cite></p>
<track id="ttrrv"><strike id="ttrrv"></strike></track>

<pre id="ttrrv"><mark id="ttrrv"></mark></pre>
    <pre id="ttrrv"><del id="ttrrv"></del></pre><p id="ttrrv"></p>
    <pre id="ttrrv"></pre>

      <noframes id="ttrrv"><del id="ttrrv"><b id="ttrrv"></b></del>
            <p id="ttrrv"></p><p id="ttrrv"></p><p id="ttrrv"></p>

            歡迎光臨濟南市天橋區昌達卷簾門加工部官網!

            聯系我們 收藏本站 在線留言

            新聞資訊

            首頁>>新聞資訊>>卷簾門安裝的相關詳細步驟說明
            新聞資訊
            聯系我們
            濟南市天橋區昌達卷簾門加工部

            聯系人:劉經理

            電話:15953131568

            網址:http://www.shaulmediation.com

            地址:濟南市天橋區金牛建材市場

            卷簾門安裝的相關詳細步驟說明

            來源:http://www.shaulmediation.com 日期:2022-08-25 發布人:hongshun
            卷簾門是現在許多大型商場或者門面所需要安裝的一種門,收縮方便,并且節省空間。下面來和濟南卷簾門廠小編一起看看卷簾門安裝的相關詳細步驟說明吧。
            Roller shutter door is a kind of door that needs to be installed in many large shopping malls or facades. It is convenient to shrink and saves space. Let's take a look at the detailed steps related to the installation of the rolling shutter door with the small editor of Jinan rolling shutter door factory.
            步驟一:做好準備
            Step 1: get ready
            1.材料:專用夾具、刮刀、粉絲袋、沖擊電鉆、手電鉆、電焊機、切割機、螺絲刀、錘子、線墜、水平尺等。
            1. Materials: special fixture, scraper, vermicelli bag, impact electric drill, hand electric drill, electric welding machine, cutting machine, screwdriver, hammer, plumb bob, level ruler, etc.
            2.工具:柱、上蓋、卷軸、刀片和導軌。
            2. Tools: center column, upper cover, reel, blade and guide rail.
            溫馨提示:以上材料都是必備工具,不能少于一個。只有他們準備充分,我們才能開始施工。
            Warm tip: the above materials are all necessary tools, and there should be no less than one. Only when they are fully prepared can we start the construction.
            步驟2:開始安裝卷簾門
            Step 2: start installation of roller shutter door
            1、確定安裝卷簾門的位置,用落線、水平儀等工具進行標記,找出水平線和垂直線。
            1. Determine the installation position of the roller shutter door, mark with tools such as falling line and level, and find out the horizontal line and vertical line.
            2.根據定位劃線開始安裝卷簾門框架。
            2. Start to install the roller shutter frame according to the positioning line.
            3.按照卷簾門機手冊中說明的方法步驟和注意事項安裝卷簾門機。
            3. Install the roller shutter door machine according to the method steps and precautions described in the roller shutter door machine manual.
            4.將組裝好的卷簾門體固定好,然后將限位器安裝在正確的位置,試運行。
            4. Fix the assembled roller shutter door, and then install the stopper at the correct position for trial operation.
            5.安裝滑道、手動機構和包裝箱。
            5. Install the slide, manual mechanism and packing box.
            步驟3:檢查結果
            Step 3: check the results
            1、調試和運行,確保各項功能和設備運行良好。
            1. Commissioning and operation to ensure that all functions and equipment operate well.
            2.一切安裝檢查完畢后,即使卷簾門安裝完畢,也能正常使用。
            2. After all installation and inspection, the roller shutter can be used normally even after installation.
            此外來看看卷簾門故障處理方法:
            Here's how to deal with the fault of roller shutter door:
            1.電機不移動或低速旋轉。這種故障通常是由斷路、電機燒毀、停止按鈕未復位、限位開關動作、重載等引起的。
            1. The motor does not move or rotates at low speed. This fault is usually caused by open circuit, motor burning, stop button not reset, limit switch action, heavy load, etc.
            濟南卷簾門廠
            處理方法:檢查線路并連接;更換燒毀的電機;更換按鈕或按幾次;撥動限位開關滑塊,使其與微動開關觸點分離,并調整微動開關位置;檢查機械部件有無卡澀,如果有,則清除卡澀并清除障礙物。
            Treatment method: check the line and connect it; Replace the burnt motor; Change the button or press it several times; Toggle the limit switch slider to separate it from the microswitch contact and adjust the position of the microswitch; Check whether the mechanical parts are jammed. If so, remove the jamming and remove the obstacles.
            2.控制故障的位置及原因:繼電器(接觸器)接觸卡死,行程微動開關故障或接觸板變形,滑塊定位螺釘松動,背板螺釘松動,使背板移位,使滑塊或螺母不能隨螺桿轉動而移動,限位器傳動齒輪損壞,按鈕上下鍵卡死。
            2. Position and cause of control fault: the relay (contactor) is stuck in contact, the travel micro switch is faulty or the contact plate is deformed, the positioning screw of the slider is loose, the screw of the back plate is loose, and the back plate is displaced, so that the slider or nut cannot move with the rotation of the screw, the transmission gear of the stopper is damaged, and the up and down keys of the button are stuck.
            處理方法:更換繼電器(接觸器);更換微動開關或觸點;擰緊滑塊螺絲,復位靠板;更換限制器的傳動齒輪;更換按鈕。
            Treatment method: replace the relay (contactor); Replace the microswitch or contact; Tighten the slider screw and reset the backup plate; Replace the transmission gear of the limiter; Replace the button.
            3.手拉鏈不動。故障原因:圓環鏈堵塞十字槽;棘爪沒有分離棘輪;壓鏈器卡住了。
            3. The hand zipper does not move. Fault cause: the ring chain blocks the cross groove; The pawl does not separate the ratchet wheel; The chain presser is stuck.
            處理方法:理順環鏈;調節棘爪與壓鏈架相對位置;更換或潤滑銷軸。
            Treatment method: straighten out the chain; Adjust the relative position of the pawl and the chain pressing frame; Replace or lubricate the pin shaft.
            以上就是卷簾門的安裝步驟,從上述文章我們可以看出,平時使用權力門的時候也要小心謹慎,要是發生了故障必須及時報修,這樣才能夠減少不必要的經濟損失。關注我們http://www.shaulmediation.com了解更多!
            The above is the installation steps of the roller shutter door. From the above article, we can see that we should be careful when using the power door at ordinary times. In case of failure, we must report for repair in time, so as to reduce unnecessary economic losses. Follow us http://www.shaulmediation.com Learn more!

            推薦閱讀/ Recommended reading

            對于我們來說卷簾門經常用來停放車庫等,不過卷簾門也時常會發生問題,比如卷簾門接通電源所有功能皆不能動作。下面濟南卷簾門廠為您進行解

            鋁合金卷簾門不能快速運行怎么辦 2022-12-22
            卷簾門的使用優勢及遇到問題該如何解決 2022-12-20
            查看問題時先看卷簾門有沒有施加作用 2022-12-17
            防火卷簾門維修常見故障及處置方式 2022-12-14

            【本站圖片均由網站所有方提供,部分圖片來源于網絡,如無意中侵犯了某媒體或個人的知識產權,請來信或來電告之,本網站將立即刪除?!?/p>

            • 宏順卷簾門
            欧美日韩国产

            <p id="ttrrv"><cite id="ttrrv"></cite></p>
            <track id="ttrrv"><strike id="ttrrv"></strike></track>

            <pre id="ttrrv"><mark id="ttrrv"></mark></pre>
              <pre id="ttrrv"><del id="ttrrv"></del></pre><p id="ttrrv"></p>
              <pre id="ttrrv"></pre>

                <noframes id="ttrrv"><del id="ttrrv"><b id="ttrrv"></b></del>
                      <p id="ttrrv"></p><p id="ttrrv"></p><p id="ttrrv"></p>