In recent years, with the improvement of the level of science and technology, the functions of the fast rolling shutter door are constantly improving. At the same time, we must pay attention to the debugging and testing of the main functions of the fast door. In general, the functional debugging and testing work of fast rolling shutter door is generally carried out from the following aspects, and the specific detection methods are as follows:

1、急停按鈕功能檢測

1. Function test of emergency stop button

急停按鈕的作用是當快速卷簾門體運行時發生緊急情況而特別設計的，它對于人身安全的保護具有積極作用。進行快速門急停按鈕功能檢測時，可以在門體運行過程中，按下這一急停按鈕，看快速門門體是否立即停止。若門體沒有立即停止，就需要檢查原因，看急停按鈕是否失靈或損壞，損壞的及要修理。

The function of emergency stop button is specially designed in case of emergency when the fast rolling shutter door is running. It has a positive effect on the protection of personal safety. When testing the function of the emergency stop button of the fast door, you can press the emergency stop button during the operation of the door body to see whether the fast door body stops immediately. If the door does not stop immediately, it is necessary to check the cause to see whether the emergency stop button is out of order or damaged, and the damaged one should be repaired.

2、紅外防砸性能調試

2. Debugging of infrared anti smashing performance

紅外防砸功能也是快速卷簾門的安全保護裝置。檢測時，可以在湖北高速門門體下落過程中，切斷紅外對射系統，看快速卷門門體是否及時反彈上升至開門位置。注意：進行紅外防砸功能測試時，一定要注意自身安全，防止紅外系統失靈造成意外事故。

The infrared anti smashing function is also the safety protection device of the fast rolling shutter door. During detection, the infrared radiation system can be cut off during the falling process of Hubei high-speed door body to see whether the fast rolling door body rebounds and rises to the opening position in time. Attention: when testing the infrared anti smashing function, you must pay attention to your own safety to prevent accidents caused by infrared system failure.

3、自動開啟功能檢測

3. Automatic opening function detection

自動開啟是快速卷簾門深受工業企業用戶喜愛的原因之一，也是高速卷簾門非常主要的功能之一。檢測這一功能，可以利用車輛、人員移動來模擬實際狀況，以=觀察門體是否能夠及時開啟以及是否全角度無死角信號覆蓋。

Automatic opening is one of the reasons why the fast rolling shutter door is deeply loved by industrial enterprise users, and it is also one of the main functions of the high-speed rolling shutter door. To detect this function, we can use the movement of vehicles and people to simulate the actual situation, so as to observe whether the door can be opened in time and whether there is no dead angle signal coverage in all angles.

4、上下限位調試檢測

4. Upper and lower limit debugging detection

上下限位位置關系著高速門的日常使用，一旦位置不準確造成快速卷簾門開啟、關閉不到位，那快速門的密封節能功能就無法得到保證。進行上下限位測試時，可以在門體靜止狀態下，按下上升按鍵，門體向上運行，待經過緩沖、完全停止后，判斷提升高度是否滿足使用方要求。如不滿足要求，再次進行調試。依照同樣的方法，按下降按鍵，待門體下落完全停止后，檢查PVC快速門門體末端停留位置是否到位，不到位的及時進行調整。

The upper and lower limit position is related to the daily use of high-speed door. Once the position is not accurate, the fast shutter door can not be opened and closed in place, so the sealing energy-saving function of the fast door can not be guaranteed. During the upper and lower limit test, when the door body is still, press the up button to move the door upward. After buffering and stopping completely, judge whether the lifting height meets the user's requirements. If the requirements are not met, debug again. According to the same method, press the down button and check whether the stop position of the PVC fast door end is in place after the door falling completely stops. If not, adjust it in time.